Qolsys IQ Panel - Adding A Z-Wave Device

Start by adding the Z-Wave devices that will be located closest to the control panel, and then move outwards. (Some devices, such as locks, must be within 6 ft of the IQ panel when adding them to the network. If a lock will not be within 6ft of the panel in its permanent installed location, consider including it in the network either before permanently mounting the panel or before installing the lock.)

Follow these directions to get to the Z-Wave menu on the IQ Panel:

screens_numbered.png

The panel will prompt you to Press the learn or pair button to add a device. Follow these directions for your specific device:

GE Plug-in Lamp or Light/Appliance Module
To add the device, double click the button in the middle of the light or appliance module.

Picture2.png

IQ Siren
To add the device, press the button at the bottom of the siren.

Screenshot_at_Feb_08_15-20-59.png

GE In-Wall Dimmer or On/Off Light Switch
To add the device, turn on and off the light switch.

Picture4.png

GE In-Wall Outlet
To add the device, double click the button in the middle of the outlet.

Picture3.png

Schlage Lever Lock or Deadbolt
On the lock keypad, enter the six-digit programming code (provided in the documentation from Schlage), then press the Schlage button, followed by 0. The Schlage button will flash orange for a minute. Wait until the light flashes green before disrupting the lock or panel. Failure to do so will result in lock malfunctions.

Kwikset Deadbolt
Open the back cover and press the white button at the top left. Wait until the red light (under the paper next to the button) stops flashing before disrupting the lock or panel. Failure to do so will result in lock malfunctions.

Picture5.png

Yale Touchscreen Deadbolt
Touch the screen with the back of your hand or fingers to activate. Then enter the 4-8 digit Master PIN code followed by the # key. Press 7 followed by the # key to enroll. Wait for the lock to announce that it has completed before disrupting the lock or panel.

GE Basic Thermostat
To add the device, press the black Mate button located under the top cover on the upper right hand side, or reset the thermostat.

9.JPG

GE Advanced Thermostat (IS-ZW-TSTAT-300)
To add the device, press the Menu button then press Mate on the screen, or reset the thermostat.1_300T.png2_300T.png

Trane Remote Energy Management Thermostat
To add the device, press the Menu button twice then scroll down to Z-Wave Install and press Select then press Yes.

1_Trane.png      2_Trane.png

IQ Thermostat
To add the device, press and hold the "Home" key for 2 seconds until you see the "NOC". Then press the "Program" key. It will display "Srh", meaning that the thermostat is searching for the network.

11.png  22.png

Once the network is found, it will show "done". Then press the "Home" key to go back to the default screen.

33.png  44.png

Once a new device has been added successfully, the panel will issue a beep, and the screen will show the device information and allow you to change the name of the device.

                                  Picture2.png

When you are finished with any changes, press Add on the panel. If the panel does not issue this confirmation, try pressing the Z-Wave device’s button again, or clicking it several time quickly.

 

 

 

For Alarm.com Smart Thermostat (ADC-T2000)

Was this article helpful?
1 out of 2 found this helpful

Comments

9 comments
  • I want to be able to add z-wave devices on my own, but I don't seem to have access to the "Installation" category of apps under Settings. How do I get access to that ?

     

  • Same problem here. My user code won't give me access to those settings and it won't take the installer code referee to here. Very frustrating. So much for simple

  • Same here, seems to have been taken out by LiveWatch during programming stage with a custom software set up.

  • anyone found a solution yet

  • Tryed to call support over and over again but no answer our call back. i havent activated my system. thinking about sending it back. Someone has a solution for this problem?

  • You need the installer code to access the installation menu. That will either be 1111 or 2222. 

     

  • 2222 worked for me.

  • Am no longer able to install Z-wave devices as I have done in the past. 1111 and 2222 both give "Invalid Code" errors. Very disappointed that I can no longer access the Install menu on my IQ panel. I have called twice and spoken to individuals who promised a tech support person would call be back, but that has not happened. Hope there is a solution to this, but if not, I will be searching for a new provider and system.

  • Hi Michael, 

    I"m sorry you're having difficulties. It sounds like your installer code has been changed from the default. I would recommend texting our digital team at 469.513.8685 for assistance. 

Please sign in to leave a comment.