2GIG GoControl - Sensor Information Sheets Pt. 2

2GIG-RPTR1-345 Wireless Repeater - Information Sheet

2GIG-RPTR1-345_Repeater_Top.jpg

Information

  • Repeats 345 MHz 2GIG and Honeywell sensors
  • 24-hour backup battery
  • 14 to 131-degree operating temperature

Power

  • 14V 1700mA power supply
  • 14500 3.7V 800mA Lithium battery (up to 24-hour backup)

Panel Compatibility 

  • 2GIG GC2 Go Control v1.16 and higher
  • 2GIG GC3 v3.1 and higher

Sensor Compatibility

  • Compatible with most 245 MHz 2GIG and Honeywell compatible wireless sensors
  • Not compatible with bi-directional sensors or 2GIG TS-1 900 MHz touchscreen

Installation

  • Mount within 100 ft of the control panel as high as possible

LED Status

  • Green ON = Power and battery OK
  • Red ON = Tamper or power failure
  • Red slow flash = Low battery
  • Red fast flash = RF Jamming
  • Blink OFF = Transmission received

 

2GIG-SDS1-345 Smoke Detector - Information Sheet

2GIG-SDS1-345_Smoke_Ring_2_jpg.jpg

Information

  • Converts existing hardwire smoke detectors to Honeywell 5800-series 345 MHz wireless
  • Only 1 sensor is needed on interconnected smoke detectors
  • Sends Smoke Alarm + SDS1-345 Low Battery, Tamper/Supervisory messages
  • 345 MHz sends supervisory signal every 70 minutes
  • 40 to 100-degree operating temperature

Battery

  • CR2032 3V Lithium, up to 3 year estimated battery life
  • 7-day battery life if AC power fails

Panel Compatibility

  • 2GIG GC2 Go Control
  • 2GIG GC3
  • 2GIG Vario

 

2GIG-TS-1 Touchscreen - Information Sheet

2GIG-TS1_v1_Touchscreen_Front_with_Display.jpg

Information

  • 4 touchscreens per system
  • Display is identical to Go Control panel
  • 918.872 MHz (Zigbee) requires 2GIG-XCVR2-345 Bi-directional transceiver module
  • OTA firmware updates from Alarm.com website will update both Go Control and TS-1
  • Local updates require 2GIG USB CABLE with pins to update TS1

Power

  • 9 to 14VDC 2GIG-AC1 power supply/transformer (Same transformer used by Go Control)
  • TS-1 v1 = 3AA Alkaline batteries
  • TS-1 v2 = No batteries, plug-in transformer connector

Part Numbers

  • 2GIG-TS1-E = English
  • 2GIG-TS1-S = Spanish
  • 2GIG-TS1-C = French

Compatibility 

  • 2GIG GC2 Go Control v1.8.1 and higher

Reset

  • Hold HOME button for 10 seconds, the keypad will reboot 

 

2GIG-TILT1-345 Tilt Sensor - Information Sheet

tile_seensor.JPG

Information

  • Activates if tilted 45 degrees from vertical
  • Hardcoded 5-second delay between activation and panel displaying open zone
  • 345 MHz sends a supervisory signal every 70 minutes
  • 2 to 120 degree operating temperature

Battery

  • CR2032 3V Lithium, 5 to 8 year battery life

Panel Compatibility 

  • 2GIG GC2 Go Control v1.14 and higher
  • 2GIG GC3 v3.1.1 and higher

Programming 

  • Tilt 5 seconds to learn
  • Program as a door sensor
  • Sensor Type: Entry Exit 1 or Entry Exit 2
  • Equipment Code: 1062 2GIG Tilt Sensor
  • Loop 1

 

2GIG-TAKE-345 Superswitch - Information Sheet

sswitch.JPG

Information

  • Converts 8 hardwire zones from an existing panel to 8 2GIG Go Control wireless zones
  • Receives power from old alarm panel backup battery 
  • 2GIG-TAK-KIT1 combines TAKE345 with enclosure and Altronix power supply
  • 345 MHz sends a supervisory signal every +7

Compatibility

  • 2GIG GC2 Go Control
  • 2GIG GC3
  • 2GIG Vario

Troubleshooting

  • Low battery trouble on Super Switch will appear as low battery trouble on all 8 wireless zones

 

2GIG-STVGRL1-345 Stove and Grill Guard Detector - Information Sheet

2GIG-STVGRL1-345_Stove___Grill_Guard_01.png

Information

  • Notifies if knob on grill or stove is left in ON position
  • Range: 100 ft recommended
  • Temperature Rating: 14 to 167 degrees

Batteries

  • Non-replaceable internal Lithium, up to 5 year battery life

Panel Compatibility 

  • 2GIG GC2 Go Control 
  • 2GIG GC3
  • 2GIG Vario
  • Honeywell Vista and Lynx

Installation

  • Remove knob and clean grill surface
  • Apply supplied adhesive strips to back to Grill Guard sensor
  • Stick sensor on grill base
  • Insert compatible sleeve over knob stem, sleeve magnet must line up with Grill Guard alignment marks while the knob is in the OFF position

 

2GIG-SMKT3-345 Smoke Heat Detector - Information Sheet

2GIG-SMKT3-345_Smoke_Heat_Detector_Top_03.jpg

 

Information

  • Smoke detector with integrated heat and freeze sensors
  • 35' protection area
  • Freeze detector activates below 41 degrees
  • Heat detector activates above 135 degrees
  • 345 MHz sends supervisory signal every 70 minutes
  • Range: 100 ft recommended
  • 35' detection range
  • Operating  temperature: 40 to 100 degrees
  • Trouble beeps can be silenced for 12 hours with test button

Battery

  • 3 AAA Alkaline, 2 to 3 year estimated battery life

 

2GIG-SMKT3-345_Smoke_Heat_Detector_Bottom_03.jpg

 

Panel Compatibility

  • 2GIG GC2 Go Control
  • 2GIG GC3
  • 2GIG Rely
  • 2GIG Vario
  • Linear PERS-4200X

Testing

  • Press and release Test button to test smoke sounder
  • Press Test for 20 seconds to trigger smoke detector test to panel

LED Status

  • Normal = Green flash every 12 seconds
  • Alarm = Red flash every second, 3-tone sounder
  • Dirty Element = Yellow blink every 8 seconds, sounder chirp every 48 seconds
  • Trouble = Yellow blink every 4 seconds, sounder chirp every 48 seconds
  • Low Battery = Yellow flash every 12 seconds, 1 chirp every 45 seconds
  • Freeze =  3 Yellow blinks every 4 seconds, no sounder
  • Tamper = Red, yellow, and green flash every 12 seconds

 

 

 

 

 

 

Was this article helpful?
0 out of 0 found this helpful

Comments

0 comments

Please sign in to leave a comment.