ADC-V523 Indoor Camera Guide

Specifications

  • 1920 x 1080p video resolution
  • HDR High Dynamic Range video recording
  • 15' night vision range
  • 117° horizontal and vertical field of view
  • 2-Way Talk / Listen
  • Micro SD slot (not functional at this time)
  • WiFi 802.11 b/g/n
  • Ethernet connection
  • Operating temperature 32° F to 104° F

ADC-V523_Indoor_Camera.jpg

Factory Default

Warning! Erases everything, camera must be re-added to Alarm.com and WiFi configured

Remove bottom rubber cover and hold WPS button 15 seconds

 ADC-V523_Indoor_Camera_WPS_Default_Button.jpg

 WiFi Setup by WPS Enrollment Mode

1. Hold WPS button for 3 seconds until front LED flashes blue 

ADC-V523_Indoor_Camera_WPS_Connection.jpg

2. Press and release router WPS button or enable WPS in router programming

Router_WPS_Button.jpg

3. Wait 2 minutes for the camera LED to flash then turn solid green if successful

ADC-V523_Indoor_Camera_Green_Light.jpg

WiFi Setup by AP Access Point Mode

1. Hold WPS button for 6 seconds until front LED flashes white

ADC-V523_Indoor_Camera_WPS_Default_Button.jpg ADC-V523_Indoor_Camera_White_Light_127x202.jpg

2. Go to smartphone WiFi settings and look for ALARM xx:xx:xx then press CONNECT

Access_Point_01_WiFi_Smartphone.png Access_Point_02_WiFi_Connect.png Access_Point_03_WiFi_Connected.png

3. Open browser and enter http://v523install/ then press SCAN for WiFi networks

Access_Point_04_Find_Out_IP_Address.png Access_Point_05_Enter_IP_Address_in_Browser.png Access_Point_06_Connected_Press_Scan.png

4. Select WiFi network, scroll up and enter encryption then press SUBMIT then OK to exit

Access_Point_07_Select_WiFi_Network.png Access_Point_08_Enter_Encryption.png Access_Point_09_Finished.png

5. Camera LED turns green if successful or red if failure

ADC-V523_Indoor_Camera_Green_Light.jpg

Hardwire Ethernet Connection to Router

Plug Ethernet cable into back of camera and into unused port on WiFi network router

ADC-V523_Camera_Connect_To_Router.jpg

Add Camera to Account by Customer Website

Note: Camera must be connected to customer's router by Ethernet cable or WiFi

 1. Login to Alarm.com customer website and press VIDEO

Alarm.com_Setup_01.png

2. Press SETTINGS

Alarm.com_Setup_02.png

3. Scroll to bottom of page and press ADD VIDEO DEVICE

Alarm.com_Setup_03.png

4. Camera should be detected, enter camera name then press INSTALL

Alarm.com_Setup_04.png

5. Alarm.com downloads information to camera, this may take up to 5 minutes

Alarm.com_Setup_05.png

6. When complete press LIVE VIEW to view camera

Alarm.com_Setup_06.png

Add Camera to Account by Smartphone App

Note: Camera must be connected to customer's router by Ethernet cable or WiFi

1. Press top left Bars to access side menu then press VIDEO then press top right GEAR icon

ADC-V523_Setup_by_App_01.png ADC-V523_Setup_by_App_02.png ADC-V523_Setup_by_App_03.png

2. Press ADD VIDEO DEVICE then press INSTALL  then enter new camera name then NEXT

ADC-V523_Setup_by_App_04.png ADC-V523_Setup_by_App_05.png ADC-V523_Setup_by_App_06.png

3. Camera may take several minutes to configure, press X at top left to exit

ADC-V523_Setup_by_App_07.png ADC-V523_Setup_by_App_08.png ADC-V523_Setup_by_App_09.png

Troubleshooting

  • Power cycle the camera by unplugging and plugging in power adapter
  • Move closer to WiFi router
  • If issues persist, try resetting the camera to factory defaults

LED Reference Guide

  • Solid Green = Local network and Internet connection OK
  • Flashing Green = Local network connection OK, Internet connection bad
  • Solid Red = No local network or Internet connection
  • Flashing Red = Camera booting
  • Flashing Blue = Camera in WPS WiFi learn mode
  • Flashing White = Camera in WiFi AP learn mode
  • Flashing Yellow = Camera in Bluetooth Pairing mode
Was this article helpful?
0 out of 0 found this helpful

Comments

0 comments

Please sign in to leave a comment.

Articles in this section