ADC-V720W Outdoor Camera Guide

This camera is discontinued but can still be added and viewed on Alarm.com account

 Specifications

  • 1280 x 800 pixel video resolution
  • 40' night vision range
  • Field of view 77° Horizontal 54° Vertical
  • WiFi 802.11 b/g/n
  • Ethernet connection
  • Does not support PoE Power over Ethernet
  • Operating Temperature -4° F to 122° F

Factory Default

Warning! Erases everything, camera must be re-added to Alarm.com and WiFi configured

 Remove plastic cover and hold Reset button 15 seconds until  LED flashes red and green

 ADC-V720W_Outdoor_Bullet_Camera_Factory_Default.jpg

Ethernet Connection to Customer's Router

Plug Ethernet cable into back of camera and back of customer network router 

ADC-V720W_Outdoor_Camera_Connect_To_Router.jpg

WiFi Setup by WPS Enrollment Mode

1. Hold WPS button 5 seconds, LED by button rapidly flashes green

ADC-V720W_WPS_Button.jpgADC-V720W_Outdoor_Bullet_Camera_Green_LED.jpg

2. Press and release WPS button on router or enable WPS in router programming

 Router_WPS_Button.jpg

3. After 2 minutes camera LED turns green if successful or red if failure

ADC-V720W_Outdoor_Bullet_Camera_Green_LED.jpg

Add Camera to Account by Customer Website

Note: Camera must be connected to customer's router by WiFi or Ethernet Connection

1. Login on a laptop or home computer to Alarm.com customer website and press VIDEO

01_Home_Page.png

2. Press SETTINGS

02_Video_Page.png

3. Scroll to bottom of page and press ADD VIDEO DEVICE

03_Video_Settings.png

4. Camera should be detected, enter camera name then press INSTALL

04_Add_V720W_Outdoor_Camera_-_Camera_Found.png

5. Alarm.com downloads information to camera, this may take up to 5 minutes

05_Add_V720W_Outdoor_Camera_-_Configuring.png

6. When complete press LIVE VIEW to view camera

06_Add_V720W_Outdoor_Camera_-_Installation_Complete.png

7. To configure wireless press SETTINGS

07_Add_Camera_-_Live_View_Program_Wireless.png

8. Scroll down to the bottom of page then press WIRELESS NETWORK

08_Add_Camera_-_Select_Wireless_Settings.png

9. Press SCAN to scan available WiFi networks

09_Add_Camera_-_Choose_Method.png

10. Select WiFi network

10_Add_Camera_-_Found_Networks.png

11. Enter WiFi encryption then press NEXT

10_Add_Camera_-_Enter_Encryption.png

12. Remove camera power, unplug Ethernet cable then power up and wait 2 minutes

11_Add_V720W_Camera_-_Wireless_Complete.png

Add Camera to Account by Smartphone App

Note: Camera must be connected to customer's router by WiFi or Ethernet Connection

1. Press top left Bars to access menu then press VIDEO then press top right GEAR icon

ADC-V720W_Setup_by_App_01.png ADC-V720W_Setup_by_App_02.png ADC-V720W_Setup_by_App_03.png

2. Press ADD VIDEO DEVICE then press INSTALL then enter name then press NEXT

ADC-V720W_Setup_by_App_04.png ADC-V720W_Setup_by_App_05.png ADC-V720W_Setup_by_App_06.png

3. Camera may take several minutes to configure, press X at top left to exit

ADC-V720W_Setup_by_App_07.png ADC-V720W_Setup_by_App_08.png ADC-V720W_Setup_by_App_09.png

 Troubleshooting

  • Power cycle the camera by unplugging and plugging in power adapter
  • Move closer to WiFi router
  • If issues persist, try resetting camera to factory defaults and reinstall

LED Reference Guide

  • All Off - No power
  • Green ON - Internet and Alarm.com connection, all OK
  • Green Flash = Local network connection, no Internet connection
  • Green Rapid Flash = WPS Enrollment mode is active
  • Red On - No local or Internet connection
  • Red Green Flash - Factory reset or firmware upgrade
Was this article helpful?
0 out of 0 found this helpful

Comments

0 comments

Please sign in to leave a comment.