Image Sensor - General Information

Specification

  • Motion detector with built-in night vision color still camera
  • 900 Mhz 802.15.4 Zigbee fi communication
  • Range 100' to panel
  • Stores event pictures then sends to Alarm.com over cellular network
  • 1 MB internal storage, stores 50 to 80 events and up to 100-160 images
  • 40 pound pet immunity
  • 35' motion detector coverage
  • 8' mounting height for most rooms, 6' for smaller rooms
  • 3 minute wait between activations to conserve battery
  • 100 minute sensor supervisory period
  • Operating temperature: 32°F to 110°F for standard motion detection
  • Operating temperature: 60°F to 110°F for pet immunity motion detection

Compatibility

Image Sensor with orange or silver sticker are compatible with...

Image_Sensor_Sticker_Orange.jpg

  • 2GIG GC3 / GC3e
  • DSC SCW9057 Impassa
  • DSC Neo with Alarm.com communicator
  • Interlogix Concord 4 with Alarm.com communicator
  • Interlogix Simon XT v1.3 and higher with Alarm.com communicator
  • Interlogix Simon XTi with Alarm.com communicator
  • Interlogix Simon XTi5 with Alarm.com communicator
  • Qolsys IQ Panel with Image Sensor receiver module
  • Qolsys IQ Panel 2, not compatible with IQ Panel 2+ with DSC PowerG receiver

Image Sensor with blue sticker are compatible with...

Image_Sensor_Sticker_Blue.jpg

2GIG GC2 GoControl and GC2e

Part Numbers

  • 2GIG-IMAGE1 - Same as Alarm,com ADC-IS-100-GC
  • 2GIG-IMAGE2-GC3 - Same as Alarm.com ADC-IS-220-LP
  • 2GIG-IMAGE3-GC3 - Same as Alarm.com ADC-IS-300-LP
  • Alarm.com ADC-IS-100-GC - Discontinued
  • Alarm.com ADC-IS-220-GC - Same as Alarm.com ADC-IS-220-LP
  • Alarm.com ADC-IS-100-LP - Discontinued
  • Alarm.com ADC-IS-200-LP - Discontinued
  • Alarm.com ADC-IS-220-LP - Discontinued
  • Alarm.com ADC-IS-221-LP - Discontinued
  • Alarm.com ADC-IS-300-LP
  • Qolsys QZ8100 - Same as Alarm.com ADC-IS-200-LP
  • Qolsys QZ8103 - Same as Alarm.com ADC-IS-300-LP
  • 2GIG-IMAGE2-GC3 - Same as Alarm.com ADC-IS-220-LP
  • 2GIG-IMAGE3-GC3 - Same as Alarm.com ADC-IS-300-LP
  • DSC IS214 - Same as Alarm.com ADC-IS-220-LP
  • DSC IS220 - Same as Alarm.com ADC-IS-221-LP

Factory Default

Insert paper-clip into front hole and hold internal button for 12 seconds

Image_Sensor_Reset_Button.jpg

Troubleshooting

  • If unable to learn factory default then try again
  • Range is less than 100' open air, less than that in the average home
  • Replace batteries with Eveready AA Lithium, using alkaline reduces battery life

                       ADC-IS-100-LP / ADC-IS-200-LP / ADC-IS-221-LP 

Image_Sensor_02_ADC-IS-100-LP.jpg

                                                           ADC-IS-300-LP

Image_Sensor_03_ADC-IS-300-LP.jpg

Was this article helpful?
0 out of 0 found this helpful

Comments

0 comments

Please sign in to leave a comment.