ADC-V520IR Indoor Camera Guide

This camera is discontinued but can still be added and viewed on an Alarm.com account

Specifications

  • 1920 x 1080p video resolution
  • 112° horizontal 100° vertical field of view
  • 20' night vision range
  • 2-Way audio
  • WiFi 802.11 b/g/n
  • Ethernet connection
  • Operating Temperature 32° F to 104° F

ADC-V520IR_Camera_Information.jpg

Factory Default

Warning! Erases everything, camera must be re-added to Alarm.com and WiFi configured 

Hold button on back of camera for 15 seconds, after 1 minute camera clicks and flashes red

ADC-V520_Reset_Button.jpg

WiFi Setup by WPS Enrollment Mode

1. Hold WPS button 5 seconds until LED flashes blue

 ADC-V520IR_WPS_Button.jpg

2.  Press and release WPS button on router or enable WPS in router programming

Router_WPS_Button.jpg

3. Camera LED turns solid green if successful

ADC-V520IR_Camera_Green_LED.jpg

 Hardwire Ethernet Connection to Router

 ADC-V520_Camera_To_Router.jpg

Add Camera to Account by Customer Website

Note: Camera must be connected to customer's router by WiFi or Ethernet Connection

1. Login to Alarm.com customer website and press VIDEO

01_Home_Page.png

2. Press SETTINGS

02_Video_Page.png

3. Scroll to bottom of page and press ADD VIDEO DEVICE

03_Video_Settings.png

4. Camera should be detected, enter camera name then press INSTALL

04_Add_V520_Camera_-_Camera_Found.png

5. Alarm.com downloads information to the camera, this may take up to 5 minutes

05_Add_V520_Camera_-_Configuring.png

6. When complete press LIVE VIEW to view camera

06_Add_V520_Camera_-_Installation_Complete.png

7. To configure WiFi press SETTINGS

07_Add_Camera_-_Live_View_Program_Wireless.png

8. Scroll down to the bottom of the page then press WIRELESS NETWORK

08_Add_Camera_-_Select_Wireless_Settings.png

9. Press SCAN to scan for networks

09_Add_Camera_-_Choose_Method.png

10. Select WiFi network

10_Add_Camera_-_Found_Networks.png

11. Enter WiFi encryption then press NEXT

10_Add_Camera_-_Enter_Encryption.png

12. Remove camera power then unplug Ethernet cable then power up and wait 2 minutes

11_Add_Camera_-_Wireless_Complete.png

Add Camera to Account by Smartphone App

Note: Camera must be connected to customer's router by WiFi or Ethernet Connection

1. Press top left Bars to access side menu then select VIDEO then press top right GEAR icon

ADC-V520_Setup_by_App_01.png ADC-V520_Setup_by_App_02.png ADC-V520_Setup_by_App_03.png 

2. Press ADD VIDEO DEVICE then press INSTALL then enter camera name then press NEXT

ADC-V520_Setup_by_App_04.png ADC-V520_Setup_by_App_05.png ADC-V520_Setup_by_App_06.png

3. Camera may take several minutes to configure, press X at top left to exit

ADC-V520_Setup_by_App_07.png ADC-V520_Setup_by_App_09.png ADC-V520_Setup_by_App_08.png

 Troubleshooting

  • Power cycle the camera by unplugging and plugging in power adapter
  • Move closer to WiFi router
  • If issues persist, try resetting the camera to factory defaults

LED Reference Guide

  • Solid Green = Local network and Internet connection OK
  • Flashing Green = Local network connection OK, Internet connection bad
  • Solid Red = No local network or Internet connection
  • Flashing Red = Camera booting
  • Flashing Blue = Camera in WPS WiFi learn mode
  • Flashing White = Camera in WiFi AP learn mode
  • Flashing Yellow = Camera in Bluetooth Pairing mode
Was this article helpful?
0 out of 0 found this helpful

Comments

0 comments

Please sign in to leave a comment.