1. Help Center
  2. Indoor Cameras
  3. ADC-V510 & ADC-V520 & ADC-V520IR

ADC-V510 Indoor Camera Guide

Avatar
Follow

This camera has been discontinued but can still be added and viewed in Alarm.com

Specifications

  • 640 x 480 pixel video resolution
  • 49.6° Horizontal 38.2° Vertical field of view
  • No night vision capability
  • WiFi 802.11 b/g
  • Ethernet connection
  • Operating Temperature 32° F to 104° F

ADC-V510_Indoor_Camera_Information.jpg

Factory Default

Warning! Erases everything, camera must be re-added to Alarm.com and WiFi configured

 Insert pin into reset hole and hold internal button 60 seconds until front LED flashes RED

ADC-V510_Reset_Button.jpg

Hardwire Ethernet Connection to Router

Note: This is required to setup WiFi and adding camera to account 

Plug Ethernet cable into back of camera and unused port on WiFi network router

ADC-V510_Camera_To_Router.jpg

 Add Camera to Account by Customer Website

 Note: Camera must be connected to customer's router by WiFi or Ethernet Connection

1. Login to Alarm.com customer website and press VIDEO

 01_Home_Page.png

2. Press SETTINGS

02_Video_Page.png

3. Scroll to bottom of page and press ADD VIDEO DEVICE

03_Video_Settings.png

4. Camera should be detected, enter name then press INSTALL

04_Add_V510_Camera_-_Camera_Found.png

5. Alarm.com downloads information to camera, this may take up to 5 minutes

05_Add_V510_Camera_-_Configuring.png

6. When complete press LIVE VIEW to view camera

06_Add_V510_Camera_-_Installation_Complete.png

7. To configure WiFi press SETTINGS

07_Add_Camera_-_Live_View_Program_Wireless.png

8. Scroll down to the bottom of the page then press WIRELESS NETWORK

08_Add_Camera_-_Select_Wireless_Settings.png

9. Press SCAN to scan for networks

09_Add_Camera_-_Choose_Method.png

10. Select WiFi network

10_Add_Camera_-_Found_Networks.png

11. Enter WiFi encryption then press NEXT

10_Add_Camera_-_Enter_Encryption.png

12. Remove power from camera, unplug Ethernet cable then plug power in and 2 minutes

11_Add_V510_Camera_-_Wireless_Complete.png

Add Camera to Account by Smartphone App

Note: Camera must be connected to customer's router by WiFi or Ethernet Connection

1. Press top left Bars to access side menu then press VIDEO then press top right GEAR icon

ADC-V510_Setup_by_App_01.png ADC-V510_Setup_by_App_02.png ADC-V510_Setup_by_App_03.png

2. Press ADD VIDEO DEVICE then press INSTALL then enter new name then press NEXT

ADC-V510_Setup_by_App_04.png ADC-V510_Setup_by_App_05.png ADC-V510_Setup_by_App_06.png

3. Camera may take several minutes to configure, press X at top left to exit

ADC-V510_Setup_by_App_07.png ADC-V510_Setup_by_App_08.png ADC-V510_Setup_by_App_09.png

Troubleshooting

  • Power cycle the camera by unplugging and plugging in power adapter
  • Move closer to WiFi router
  • If issues persist, try resetting the camera to factory defaults

LED Reference Guide

  • Solid Green = Local network and Internet connection OK
  • Flashing Green = Local network connection OK, Internet connection bad
  • Solid Red = No local network or Internet connection
  • Flashing Red = Camera booting
  • Flashing Blue = Camera in WPS WiFi learn mode
  • Flashing White = Camera in WiFi AP learn mode
  • Flashing Yellow = Camera in Bluetooth Pairing mode
Was this article helpful?
0 out of 0 found this helpful

Comments

0 comments

Please sign in to leave a comment.

Articles in this section