Specifications

  • 1920 x 1080 pixel video resolution
  • 117° vertical and horizontal field of view
  • 40' night vision range
  • WiFi 802.11 b/g/n
  • Micro SD slot (not functional at this time)
  • Operating Temperature -4° F to 122° F

mceclip0.png

 

Factory Default

Warning! Erases everything, the camera must be re-added to Alarm.com and Wi-Fi configured

 Remove cover and hold reset button 15 seconds, camera clicks and flashes red

 

ADC-V723_Outdoor_Camera_Reset_Button.jpg

 

Pre-installation Steps

This brief video reviews pre-installation steps for the Brinks Home Outdoor Camera (ADC-V723):

 

Wi-Fi Setup by WPS Enrollment

This brief instructional video demonstrates how to successfully pair the Brinks Home Outdoor Camera (ADC-V723) to a router using WPS mode:

 

Step-by-step instructions:

1. Hold the reset button for 3 seconds until the front LED flashes blue

ADC-V723_Outdoor_Camera_WPS_Connection.jpg

2. Press and release the router's WPS button or enable WPS in router programming

Router_WPS_Button.jpg

 

3. The LED on the camera may turn red during this step. Wait 2 minutes for the camera LED to flash then turn solid green if successful.

ADC-V723_Outdoor_Camera_Green_Light.jpg

Note: If WPS Mode fails, try Access Point Mode

 

Wi-Fi Setup by Access Point

This brief instructional video demonstrates how to successfully pair the Brinks Home Outdoor Camera (ADC-V723) to a router using Access Point (AP) mode:

 

 

Step-by-step instructions:

1. Hold the reset button for 6 seconds until the front LED flashes white to begin AP mode. This will also happen automatically after powering up the camera.

ADC-V723_Outdoor_Camera_AP_Mode.jpg

 

2. Go to smartphone Wi-Fi settings and find ADC-V723 (xx:xx:xx), then press CONNECT

Access_Point_01_WiFi_Smartphone.png Access_Point_02_WiFi_Connect.png Access_Point_03_WiFi_Connected.png

 

3. In a web browser, go to http://v723install/ then press SCAN for Wi-Fi networks

Access_Point_04_Find_Out_IP_Address.png Access_Point_05_Enter_IP_Address_in_Browser.png Access_Point_06_Connected_Press_Scan.png

 

4. Select Wi-Fi network, scroll up and enter your Wi-Fi credentials, press SUBMIT, then OK

Access_Point_07_Select_WiFi_Network.png Access_Point_08_Enter_Encryption.png Access_Point_09_Finished.png

 

5. Camera LED turns green if successful or red if failure

ADC-V723_Outdoor_Camera_Green_Light.jpg

Add Camera using the Brinks Home App Website

 Note: Camera must be connected by Wi-Fi to router

 

1. Login to the Brinks Home App website (powered by Alarm.com) and select VIDEO

01_Add_V723_Camera_-_Home_Page.png

 

2. Select SETTINGS

02_Add_V723_Camera_-_Video_Page.png

 

3. Scroll to bottom of page and select ADD VIDEO DEVICE

03_Add_V723_Camera_-_Video_Settings.png

 

4. Camera should be detected, enter camera name, then select INSTALL

04_Add_V723_Camera_-_Camera_Found.png

 

5. The camera is added to the network, which can take several minutes

05_Add_V723_Camera_-_Configuring.png

 

6. When finished select LIVE VIEW to view images from newly installed camera

06_Add_V723_Camera_-_Installation_Complete.png

 

Add Camera using the Brinks Home Mobile App

Note: Camera must be connected to customer's router by WiFi

 

This brief instructional video demonstrates how to successfully add the Brinks Home Indoor Camera (ADC-V523) to the Brinks Home Mobile App:

 

Step-by-step instructions:

1. From the menu icon mceclip1.png in the top left, press + Add Device, then press Video Camera

mceclip4.png mceclip5.png mceclip7.png

 

2. Select the camera or enter the MAC address, tap Install, Name your camera, then press Next

 mceclip8.png mceclip9.png mceclip10.png

 

3. Camera may take several minutes to configure. Press Next when finished.

mceclip11.png mceclip12.png 

 

4. Tap the play icon to confirm the live view, view live video in full screen to test Two-Way Audio, test speaker to mute and unmute, and test the microphone. Installation is complete!

 

Troubleshooting

  • Power cycle the camera by unplugging and plugging in power adapter
  • Move closer to Wi-Fi router
  • If issues persist, try resetting camera to factory defaults and reinstall

 

LED Reference Guide

  • All Off - No power
  • Blue Blink - WPS Enrollment mode enabled
  • Blue On - Privacy Mode enabled, press and release corner privacy button
  • Red On - No local or Internet connection
  • Red Flash - Not programmed
  • Red / Green Blink - Restoring factory defaults
  • Green Blink - Local Network connection
  • Green On - Internet and Alarm.com connection
Was this article helpful?
0 out of 2 found this helpful