GC3 - Add Z-Wave Device

Enter Programming

1. Press SYSTEM SETTINGS then enter Installer Code 1561

Disarmed.jpg Enter_Code.png


 Settings_Menu.png Add_Device_01.png

3. GC3 enters Z-Wave learn mode


GE Jasco Plug-in Lamp Appliance Module

Double click Mate button twice


FortrezZ SSA1 Indoor Siren

Bring siren within 6' of GoControl then press Program Switch twice


Everspring SE812 Indoor Siren

Press LINK button inside battery compartment 3 times


GE Jasco Wall Dimmer Light Switch

Turn the light switch on and off


GE Jasco Wall AC Outlet

Double click button in the middle of the outlet.


Schlage Deadbolt Door Lock

1. Enter 6-digit programming code provided in the Schlage documentation

2. Press SCHLAGE button then 0, The Schlage button flashes orange


Kwikset Deadbolt Door Lock

Open the battery cover and press left SmartCode button


Yale Touchscreen Deadbolt Door Lock

1. Touch screen with the back of your hand or fingers to activate

2. Enter 4 to 8-digit Master Code then press #, lock should sound Happy tone

3. Press 7 then # to learn, lock should sound Happy tone


GE Radio Thermostat CT20 Basic Thermostat
Remove top cover then press the MATE button


Alarm.com ADC-T2000 Thermostat

1. Press MODE button to display temperature, press MODE until heat/cool icons disappear

T2000_Setup_03.jpg T2000_Setup_02.jpg

2. Hold DOWN ARROW until Radio Wave Icon appears below temperature display 


Alarm.com ADC-T3000 Thermostat

1. Press MENU button to display Menu then press DOWN ARROW until SETTINGS

Alarm.com_ADC-T3000_Learn_00.jpg Alarm.com_ADC-T3000_Learn_01.jpg

2.  Press ENTER button to select then press DOWN ARROW until NETWORK 

Alarm.com_ADC-T3000_Learn_02.jpg Alarm.com_ADC-T3000_Learn_03.jpg

3. Press ENTER button to select then press UP or DOWN ARROW to highlight ADD

Alarm.com_ADC-T3000_Learn_04.jpg Alarm.com_ADC-T3000_Learn_05b.jpg

4. Press ENTER button to select and start Z-Wave learn mode

Alarm.com_ADC-T3000_Learn_05.jpg Alarm.com_ADC-T3000_Learn_06.jpg

5. Learning may take up to 1 minute to complete and exit


Radio Thermostat CT30, CT100, CT101


1. Press thermostat MENU button, r1 displays and MATE appears under antenna icon

Radio_Thermostat_CT100_Learn_01_Press_Menu.jpg Radio_Thermostat_CT100_Learn_02_Press_Mate.jpg

2. Press MATE button again, MATE begins flashing

Radio_Thermostat_CT100_Learn_03_Mate_Flashes.jpg Radio_Thermostat_CT100_Learn_03_Mate_Flashes__1_.jpg

3. If successful thermostat displays LINK under antenna icon, press MENU button to exit


Radio Thermostat CT110 Thermostat


 GoControl RCS TBZ-48 Thermostat

1. Hold FAN button 5 seconds until SETUP appears then UP ARROW button until ZWAVE


2. Press MODE button to select then press MODE button again to learn

GoControl_Thermostat_Learn_03.jpg GoControl_Thermostat_Learn_04.jpg

3. If successful press FAN button to exit, antenna icon appears by temperature display

GoControl_Thermostat_Learn_05.jpg GoControl_Thermostat_Learn_06.jpg

Trane Thermostat

Press LEFT button twice then scroll down to Z-WAVE INSTALL and press SELECT then YES

final_2.jpg final_cuatro.jpg

Linear GoControl Garage Door Controller

Press MATE button, Linear controller sounds 1 beep then 3 beeps if successful


4. Learning may take up to 1 minute, when finished press OK

Add_Device_03.png Add_Device_04.png

5. Press RENAME then enter light module name then press DONE

Add_Device_05.png Add_Device_06.png

6. Press GC3_Back_Arrow.png or the HOME button to exit

Add_Device_07.png GC3_Home_Button_2.jpg

Was this article helpful?
0 out of 1 found this helpful