Connecting Alula RE609 Glassbreak Detector to the 2GIG GoControl Panel

Please follow the steps below to connect your wireless Alula RE609 Glassbreak Detector to the 2GIG GoControl Panel.

 

1. Press the bottom right logo, enter Installer Code 1561 or 1171, then press system configuration

001a_Enter_Programming_Mode_-_Programming_-_Enter_Program_01_278x158.png 001b_User_Menu_-_Disarm_05_278x158.png 001c_Programming_-_Enter_Program_03_278x158.png

 

2. From here, you've entered Q1: RF sensor programming. Press GO TO, enter a 2-digit location number between 01 and 60, then press the down arrow to continue

002a_Programming_-_Enter_Program_04_278x158.png 002c_Programming_-_Enter_Program_05_278x158.png

 

3. To select your sensor type, enter 01, 02, or 03, or press the arrow buttons to scroll through the following options: (01) Exit/Entry 1, (02) Exit/Entry 2, or (03) Perimeter. Next, press the down arrow to continue.

002a_2GIG_Q1_RF_Sensor_Programming_02_Type_278x158.png

 

4. To specify the equipment type, press the arrow buttons to scroll to (0104) Glass Break. Press the down arrow to continue.

003aV2-GLASSBREAK_TYPE_2GIG_Q1_RF_Sensor_Programming_02.png

 

5. Enter the serial number from the sensor sticker. Alternatively, you can press shift, then press learn, then press the enrollment button on the glassbreak sensor, and then press OK. Once the serial number is entered manually or through the alternative process, press the down arrow to continue.

004a_2GIG_Q1_RF_Sensor_Programming_05_Serial_Number_1_278x158.png 004b_2GIG_Q1_RF_Sensor_Programming_05_Serial_Number_2_278x158.png 004c_2GIG_Q1_RF_Sensor_Programming_05_Serial_Number_3_278x158.png

 

6. Enter 0, then press the down arrow to continue

006a_2GIG_Q1_RF_Sensor_Programming_06_Equipment_Age_278x158.png

 

7. Enter 1 if using an external switch or 2 if using an internal reed switch, then press the down arrow to continue

007a_2GIG_Q1_RF_Sensor_Programming_07_Loop_Number_278x158.png

 

8. Enter 1 to enable the 30-second dialer delay, then press the down arrow to continue

008a_2GIG_Q1_RF_Sensor_Programming_08_Dialer_Delay_278x158.png

 

9. Press insert and use the arrows to select a voice descriptor for the sensor, then press the down arrow to continue. Note: multiple words can be added by pressing insert again.

009a_2GIG_Q1_RF_Sensor_Programming_09_Description_1_Blank_278x158.png 009b_2GIG_Q1_RF_Sensor_Programming_09_Description_2_Front_278x158.png

 

10. Enter 1 to enable central station reports, then press the down arrow to continue

010a_2GIG_Q1_RF_Sensor_Programming_09_Description_3_Front_Door_278x158.png

 

11. Enter 1 to enable sensor supervision, then press the down arrow to continue

011a_2GIG_Q1_RF_Sensor_Programming_10_Reports_278x158.png

 

12. Press the arrow buttons to scroll through numbered chime sounds, then press the down arrow to continue

012a_2GIG_Q1_RF_Sensor_Programming_11_Supervision_278x158.png

 

13. Press the down arrow to complete the process or press EDIT NEXT to program in the next sensor

 014a_2GIG_Q1_RF_Sensor_Programming_13_Summary_1_278x158.png

Was this article helpful?
0 out of 0 found this helpful