
Mark Leuck
- Total activity 682
- Last activity
- Member since
- Following 0 users
- Followed by 2 users
- Votes 0
- Subscriptions 278
Activity overview
Latest activity by Mark Leuck-
Mark Leuck created an article, ADC-SG130 WiFi Gateway Guide
Hardwire connection to Internet Router for up to 4 WiFi cameras Specifications 2.4 GHz, does not support 5 GHz devices WiFi 8021.11 b/g/n/ac Ethernet connection Operating temperature 32° F to 104°...
- Edited
- 1 follower
- 0 comments
- 0 votes
-
Mark Leuck commented, Official commentI believe the WallSwipe connects to an Aeotech Nano dimmer module, I assume that is already learned into the IQ Panel You would then have to go to your Alarm.com account and setup a rule to opera...
- View comment
- 0 votes
-
Mark Leuck created an article, Lynx Touch - Delete Z-Wave Device
1. Press AUTOMATION then TOOLS 2. Press EXCLUDE DEVICES then enable Z-Wave delete mode on device GE Jasco Light Appliance Module Double click MATE / LEARN button GE Jasco Wall Dimmer Lght ...
- Edited
- 1 follower
- 0 comments
- 0 votes
-
Mark Leuck created an article, Lynx Touch - Delete Failed Z-Wave Device
1. Press AUTOMATION then PRESS TO SEE FAILED DEVICES 2. Select device then press FIX IT 3. When finished press BACK ARROW or the HOME button to exit
- Edited
- 1 follower
- 0 comments
- 0 votes
-
Mark Leuck created an article, Lynx Touch - Add Z-Wave Device
1. Press AUTOMATION then TOOLS 2. Press INCLUDE DEVICES to begin Z-Wave device enrollment 3. Set Z-Wave device to learn mode GE Jasco Light Appliance Module Double click MATE / LEARN button ...
- Edited
- 1 follower
- 0 comments
- 0 votes
-
Mark Leuck created an article, Lynx Touch - Replace Backup Battery
1. Press top tabs with screwdriver then pull front face-plate down 2. Remove battery holder screw then unplug battery from circuit board and remove 3. Honeywell LYNXRCHKIT-SC 7.2 Volt 1100 mA bat...
- Edited
- 1 follower
- 0 comments
- 0 votes
-
Mark Leuck created an article, Interlogix Simon XTi Battery Replacement
1. Insert coin into bottom right corner slot then twist to remove front bezel 2. Pry top tabs up then fold down front cover 3. Unplug battery and remove battery pack 4. 6 Volt 2100 mA battery is...
- Edited
- 1 follower
- 0 comments
- 0 votes
-
Mark Leuck created an article, Lynx Touch - Program WiFi by WPS
1. Press SECURITY then press bottom right MORE tab 2. Press TOOLS then enter the Master Code 3. Press WiFi CONFIG then press press WPS button or enable WPS in router programming 4. Press WPS...
- Edited
- 1 follower
- 0 comments
- 0 votes
-
Mark Leuck created an article, Lynx Touch - Program WiFi
1. Press SECURITY then press bottom right MORE tab 2. Press TOOLS then enter the Master Code 3. Press WiFi CONFIG then press SCAN ACCESS POINTS 4. Select WiFi network then press EDIT then pre...
- Edited
- 1 follower
- 0 comments
- 0 votes
-
Mark Leuck created an article, Lynx Touch - Messages
The Lynx Touch can record several messages up to 184 seconds total length Record Message 1. Press SECURITY and MESSAGE 2. Press ADD NEW then RECORD then begin speaking the message 3. When the m...
- Edited
- 1 follower
- 0 comments
- 0 votes